« previous next »
Pages: [1]   Go Down

Author Topic: Ilmberger hugger  (Read 2988 times)

0 Members and 1 Guest are viewing this topic.

Offline baldbiker

  • Full Member
  • ***
  • Posts: 194
  • Karma: +1/-0
    • View Profile
  • My K bike model:: K1300s
  • Location:: Ashford Surrey
Ilmberger hugger
« on: August 25, 2017, 07:52:28 pm »
I had my tyre changed to the roadtec 01 on Wed and it is catching on the tyre on the right side worse than it did on the M3.
The hugger was second hand and advertised for k1300s is the any way to tell if it's for the 50 profile tyre.  I can't see a part number. Feeling peed off.
Logged

Offline Costas

  • Hero Member
  • *****
  • Posts: 4322
  • Karma: +63/-1
  • Riders drive K, a Hawk flies, both are fast
    • View Profile
  • My K bike model:: K1300S
  • Modifications and add-ons:: BMW Motorrad rider and pillion HP4 pegs,10-30 lit tank bag, SENA for BMW intercom system. Evo air filters. TechSpec tank pads. MIZU lowering dogbone system. B2 accelerator. Wunderlich adjustable levers, hub , brake caliber protectors, duolever bold protector. Turatech ABS Sensor protectors. IDE bars. Rizoma rear led signal lights, bar ends with lever protectors. Sargent complete system seat (pod, pillion backrest). Shrodie side badge led signal lights two modes. LED lights 2X35W 3000k high beam, 10W parking two modes. Tracker. Metisse front wheel protector sliders. R&G water pump protector, cardan protector. Ilmberger carbon set. Ztechnic tank protector,DT wimglets.
  • Location:: Athens, Greece, KS-Loutsa 37°58'16.6"N 23°59'06.8"E 37.971269, 23.985224
Re: Ilmberger hugger
« Reply #1 on: August 26, 2017, 09:47:10 am »
If it was for a 1200 bike it's narrower so need to trim it.
Logged
Embrace the wind.

Offline baldbiker

  • Full Member
  • ***
  • Posts: 194
  • Karma: +1/-0
    • View Profile
  • My K bike model:: K1300s
  • Location:: Ashford Surrey
Re: Ilmberger hugger
« Reply #2 on: August 26, 2017, 01:21:24 pm »
Has anyone got a measurement from edge to edge please. It seems to be in one area, it's coming of later to check properly.
Logged

Offline baldbiker

  • Full Member
  • ***
  • Posts: 194
  • Karma: +1/-0
    • View Profile
  • My K bike model:: K1300s
  • Location:: Ashford Surrey
Re: Ilmberger hugger
« Reply #3 on: August 26, 2017, 03:49:45 pm »
The only numbers I can find are.  100351Q and another which I presume is from a post production check..
Logged

Offline Mikek7

  • Newbie
  • *
  • Posts: 16
  • Karma: +0/-0
    • View Profile
  • My K bike model:: K1300S
  • Modifications and add-ons:: none ... yet
  • Location:: Neston, Wirral
Re: Ilmberger hugger
« Reply #4 on: August 27, 2017, 11:14:48 am »
I also have an Ilmberger hugger and Roadtec 01s on a K1300S - no clearance problems.
There is approx 10mm clearance on each side. Bit difficult to get an accurate measurement without taking it off, but it seems to be 205mm.

Left and right pictures here ... and yes, its dirty after this mornings ride :)
https://goo.gl/photos/GRgXn9d9f3Phz2PX8
https://goo.gl/photos/uPtKa55BQt4Pf9Pz7
« Last Edit: August 27, 2017, 11:34:20 am by Mikek7 »
Logged

Offline baldbiker

  • Full Member
  • ***
  • Posts: 194
  • Karma: +1/-0
    • View Profile
  • My K bike model:: K1300s
  • Location:: Ashford Surrey
Re: Ilmberger hugger
« Reply #5 on: August 27, 2017, 01:15:55 pm »
Thanks for those . It seem to be catching at the top to the right of centre.
Logged

Offline baldbiker

  • Full Member
  • ***
  • Posts: 194
  • Karma: +1/-0
    • View Profile
  • My K bike model:: K1300s
  • Location:: Ashford Surrey
Re: Ilmberger hugger
« Reply #6 on: September 07, 2017, 06:12:28 pm »
I've contacted ilmberger last week with the numbers I had and they have promptly replied bit with no real answer as yet.
Would spacing the hugger to bring it to the right a few mm help.
Logged
Pages: [1]   Go Up
« previous next »